In this post i am going to explain how to brew Trenabolone Acetate (Tren Ace), first is a list for what you will need.
1. Two 500ml pyrex pot
2. A 500 ml glass beaker
3. 250 ml of Benzyl Alcohol
4. 250 ml of Benzyl Benzoate
5 1000 ml of MCT oil make sure its 100 percent MCT. you can use grap seed oil or cotton seed oil. Mct is the best
6. 60 grams of Trenabolone Acetate.
7. 2 60ml syringe and three 3 ml syringe you was also 18 or 22 guage needles.
8. 1 500ml complete bottle top filtration system the filter 0.22um one 0.45um complete 500ml filtration system. These are sometimes hard to get so if you want to go old school you can use the syringe filter. you would need two 0.22um filters and two 0.45um syringe filter.
Now once you have this list its time to cook. Remember most steroids can be brewed with these solvents you would just change the active compound. You will need a big pot one you would use to boil water or you can use a hot plate with a magnetic stir. The way im going to show you is the economic way to brew.
This recipe i am giving you will yield 50, 10ml bottles at a 10 percent overdose just in case your raw material isnt 99 percent pure and to make a very strong finished product that will give insane gains. This recipe will give you dosage of 100 mg per 1 ml.
Here is the recipe you will use.
1. 60 grams of trenabolone acetate
2. ba 10 ml this 0.1% of the total brew keeps the gear sterile
3. bb 90ml this is 0.18% percent of the total brew. bb keeps the gear in liquid form prevents crashing which is when the oil turns into a crystal soild state
4. 358 ml of Mct oil this is your carrier oil. the oil that will carry the hormone into your body.
Little tip when it comes to ba and bb less is more so the less solvents used the better. too much Benzyl Benzoate or Benzyl Alcohol the injection will sting when injecting and will give you a bad post injection pain.
This the BB and the BA i used. that is also the Raw Tren Ace powder (60 Grams)
This photo is now all 3 solvents (BB BA MCT) MCT oil is in the Pyrex
In that glass beaker that is the BB BA mixed together. Now you add in the raws and stir them together
Same part of the process from the picture before this one
Now you poor into the pyrex with the MCT oil and mix it all together
Now you put that pyrex into a pot oh boiling water and water bath it. continue stiring while water bathing the gear
now you stir and cook it until you see no hormone swirls and no crystals aka the hormone crytals
you can now see how clear the gear is becoming. you are almost done
Now after all of that you must let it cool off before putting it through the auto fill filters.
This is called a complete bottle top filtration system. you need a small vacuum pump to apply vacuum pressure
this filter is a .22 filter
this last step is the same as before but this 2nd filter is a .45. i filter twice because it makes it not feel like motor oil going into the ass checks
1. Two 500ml pyrex pot
2. A 500 ml glass beaker
3. 250 ml of Benzyl Alcohol
4. 250 ml of Benzyl Benzoate
5 1000 ml of MCT oil make sure its 100 percent MCT. you can use grap seed oil or cotton seed oil. Mct is the best
6. 60 grams of Trenabolone Acetate.
7. 2 60ml syringe and three 3 ml syringe you was also 18 or 22 guage needles.
8. 1 500ml complete bottle top filtration system the filter 0.22um one 0.45um complete 500ml filtration system. These are sometimes hard to get so if you want to go old school you can use the syringe filter. you would need two 0.22um filters and two 0.45um syringe filter.
Now once you have this list its time to cook. Remember most steroids can be brewed with these solvents you would just change the active compound. You will need a big pot one you would use to boil water or you can use a hot plate with a magnetic stir. The way im going to show you is the economic way to brew.
This recipe i am giving you will yield 50, 10ml bottles at a 10 percent overdose just in case your raw material isnt 99 percent pure and to make a very strong finished product that will give insane gains. This recipe will give you dosage of 100 mg per 1 ml.
Here is the recipe you will use.
1. 60 grams of trenabolone acetate
2. ba 10 ml this 0.1% of the total brew keeps the gear sterile
3. bb 90ml this is 0.18% percent of the total brew. bb keeps the gear in liquid form prevents crashing which is when the oil turns into a crystal soild state
4. 358 ml of Mct oil this is your carrier oil. the oil that will carry the hormone into your body.
Little tip when it comes to ba and bb less is more so the less solvents used the better. too much Benzyl Benzoate or Benzyl Alcohol the injection will sting when injecting and will give you a bad post injection pain.
This the BB and the BA i used. that is also the Raw Tren Ace powder (60 Grams)
This photo is now all 3 solvents (BB BA MCT) MCT oil is in the Pyrex
In that glass beaker that is the BB BA mixed together. Now you add in the raws and stir them together
Same part of the process from the picture before this one
Now you poor into the pyrex with the MCT oil and mix it all together
Now you put that pyrex into a pot oh boiling water and water bath it. continue stiring while water bathing the gear
now you stir and cook it until you see no hormone swirls and no crystals aka the hormone crytals
you can now see how clear the gear is becoming. you are almost done
Now after all of that you must let it cool off before putting it through the auto fill filters.
This is called a complete bottle top filtration system. you need a small vacuum pump to apply vacuum pressure
this filter is a .22 filter
this last step is the same as before but this 2nd filter is a .45. i filter twice because it makes it not feel like motor oil going into the ass checks